TOYOTA生产的Crankshaft Main Bearing-第三方配件-宜配网-专业汽配网

也可拖拽图片到此处自动识别，或在微信/QQ截图后点击此处后Ctrl+V

参考号	零件	参数
ENGINETECH : BC1027	Crankshaft Main Bearing
MAHLE / CLEVITE : MS2298A	Crankshaft Main Bearing	A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; D Bearing has dowel hole.: S Indicates a set number designation. ; G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ;
ITM ENGINE COMPONENTS : 4M3956	Crankshaft Main Bearing
ITM ENGINE COMPONENTS : 7M9700	Crankshaft Main Bearing
ENGINETECH : BC1032	Crankshaft Main Bearing	Maximum Clearance: 0.0010-0.0019 ; Position: 1-2-3-4 ; Shaft Diameter: 2.4001-2.4016 ; Width: 0.708 ;
MAHLE / CLEVITE : MS2357A	Crankshaft Main Bearing	A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; D Bearing has dowel hole.: S Indicates a set number designation. ; G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ;
ITM ENGINE COMPONENTS : 5M1704	Crankshaft Main Bearing
ENGINETECH : BC1048	Crankshaft Main Bearing
MAHLE / CLEVITE : MS2361A	Crankshaft Main Bearing	A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; D Bearing has dowel hole.: S Indicates a set number designation. ; G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ;
ITM ENGINE COMPONENTS : 5M2184	Crankshaft Main Bearing
ENGINETECH : BC1046	Crankshaft Main Bearing
MAHLE / CLEVITE : MS2376A	Crankshaft Main Bearing	A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; D Bearing has dowel hole.: S Indicates a set number designation. ; G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ;
ENGINETECH : BC1002	Crankshaft Main Bearing	Maximum Clearance: 0.0005 ; Maximum Housing Inside Diameter: 2.3228-2.3235 ; Position: 1-5 ; Shaft Diameter: 2.1648-2.1654 ; Wall Thickness: 0.0781-0.0786 ; Width: 0.669 ;
MAHLE / CLEVITE : MS2243A	Crankshaft Main Bearing	A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; D Bearing has dowel hole.: S Indicates a set number designation. ; G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ;
ITM ENGINE COMPONENTS : 5M9533	Crankshaft Main Bearing
SEALED POWER : 7469M	Crankshaft Main Bearing	Bearing 1: 72.01 mm housing bore Max; oil clearance Max 0.038 mm; Length 21.00 Max; wall thickness 2.20 Max ; Bearing 1 Qty: 5 ;
MAHLE / CLEVITE : MS2365A	Crankshaft Main Bearing	A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; D Bearing has dowel hole.: S Indicates a set number designation. ; G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ;
MAHLE / CLEVITE : MS2268A	Crankshaft Main Bearing	A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; D Bearing has dowel hole.: S Indicates a set number designation. ; G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ;
ENGINETECH : BC1028	Crankshaft Main Bearing
ITM ENGINE COMPONENTS : 5M1046	Crankshaft Main Bearing
ENGINETECH : BC1214	Crankshaft Main Bearing	Maximum Clearance: 0.0004-0.0009 ; Maximum Housing Inside Diameter: 1.9685-1.9692 ; Position: 1-2-3-4-5 ; Shaft Diameter: 1.8106-1.8110 ; Shell Part Number: M5394-U/L ; Wall Thickness: 0.0782-0.0787 ; Width: 0.630 ;
ITM ENGINE COMPONENTS : 5M9530	Crankshaft Main Bearing
ITM ENGINE COMPONENTS : 4M8379	Crankshaft Main Bearing
MAHLE / CLEVITE : MS2240P	Crankshaft Main Bearing	A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; D Bearing has dowel hole.: S Indicates a set number designation. ; G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ;
ENGINETECH : BC1534	Crankshaft Main Bearing	Maximum Clearance: 0.0011-0.0031 ; Maximum Housing Inside Diameter: 2.5984-2.5992 ; Position: 1-4 ; Shaft Diameter: 2.4011-2.4016 ; Shell Part Number: T2A ; Wall Thickness: 0.0974-0.0979 ; Width: 0.886 ;
MAHLE / CLEVITE : MS2267A	Crankshaft Main Bearing	A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; D Bearing has dowel hole.: S Indicates a set number designation. ; G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ;
ENGINETECH : BC1543	Crankshaft Main Bearing	Maximum Clearance: 0.0016-0.0023 ; Maximum Housing Inside Diameter: 2.8346-2.8353 ; Position: 1-5 ; Shaft Diameter: 2.6373-2.6378 ; Wall Thickness: 0.0977-0.0982 ; Width: 0.883 ;
MAHLE / CLEVITE : MS2284A	Crankshaft Main Bearing	A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; D Bearing has dowel hole.: S Indicates a set number designation. ; G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ;
MAHLE / CLEVITE : MS2336A	Crankshaft Main Bearing	A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; D Bearing has dowel hole.: S Indicates a set number designation. ; G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ;
ITM ENGINE COMPONENTS : 5M9137	Crankshaft Main Bearing
ENGINETECH : BC1042	Crankshaft Main Bearing
ENGINETECH : BC1008	Crankshaft Main Bearing	Maximum Clearance: 0.0006-0.0013 ; Maximum Housing Inside Diameter: 2.0493-2.0498 ; Position: 1-2-3-4-5 ; Shaft Diameter: 1.8893-1.8897 ; Shell Part Number: MB5287U/L ; Wall Thickness: 0.0785-0.0790 ; Width: 0.669 ;
SEALED POWER : 7354MA	Crankshaft Main Bearing	Part Material: A-Series aluminum ;
ENGINETECH : BC1014	Crankshaft Main Bearing	Maximum Clearance: 0.0006-0.0013 ; Maximum Housing Inside Diameter: 2.0473-2.0478 ; Position: 1-2-3-4-5 ; Shaft Diameter: 1.8893-1.8897 ; Shell Part Number: M5375U/L ; Wall Thickness: 0.0782-0.0787 ; Width: 0.661 ;
MAHLE / CLEVITE : MS2014A	Crankshaft Main Bearing	A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; D Bearing has dowel hole.: S Indicates a set number designation. ; G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ;
MAHLE / CLEVITE : MS2014HX	Crankshaft Main Bearing	A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; D Bearing has dowel hole.: S Indicates a set number designation. ; G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ;
MAHLE / CLEVITE : MS2014H	Crankshaft Main Bearing	A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; D Bearing has dowel hole.: S Indicates a set number designation. ; G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ;
ITM ENGINE COMPONENTS : 5M9531	Crankshaft Main Bearing
ITM ENGINE COMPONENTS : 5M9532	Crankshaft Main Bearing
ENGINETECH : BC1437	Crankshaft Main Bearing
ITM ENGINE COMPONENTS : 4M9220	Crankshaft Main Bearing
SEALED POWER : 7261M	Crankshaft Main Bearing	Part Material: Steel backed overplated bronze alloy ;
ENGINETECH : BC1435	Crankshaft Main Bearing
ITM ENGINE COMPONENTS : 5M9422	Crankshaft Main Bearing
MAHLE / CLEVITE : MS2212A	Crankshaft Main Bearing	A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; D Bearing has dowel hole.: S Indicates a set number designation. ; G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ;
SEALED POWER : 7391M	Crankshaft Main Bearing	Part Material: Steel backed overplated bronze alloy ;

参考号

零件

参数

ENGINETECH : BC1027

Crankshaft Main Bearing

MAHLE / CLEVITE : MS2298A

Crankshaft Main Bearing

A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ;
B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
D Bearing has dowel hole.: S Indicates a set number designation. ;
G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ;
HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ;
K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ;

ITM ENGINE COMPONENTS : 4M3956

Crankshaft Main Bearing

ITM ENGINE COMPONENTS : 7M9700

Crankshaft Main Bearing

ENGINETECH : BC1032

Crankshaft Main Bearing

Maximum Clearance: 0.0010-0.0019 ;
Position: 1-2-3-4 ;
Shaft Diameter: 2.4001-2.4016 ;
Width: 0.708 ;

MAHLE / CLEVITE : MS2357A

Crankshaft Main Bearing

A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ;
B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
D Bearing has dowel hole.: S Indicates a set number designation. ;
G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ;
HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ;
K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ;

ITM ENGINE COMPONENTS : 5M1704

Crankshaft Main Bearing

ENGINETECH : BC1048

Crankshaft Main Bearing

MAHLE / CLEVITE : MS2361A

Crankshaft Main Bearing

A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ;
B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
D Bearing has dowel hole.: S Indicates a set number designation. ;
G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ;
HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ;
K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ;

ITM ENGINE COMPONENTS : 5M2184

Crankshaft Main Bearing

ENGINETECH : BC1046

Crankshaft Main Bearing

MAHLE / CLEVITE : MS2376A

Crankshaft Main Bearing

A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ;
B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
D Bearing has dowel hole.: S Indicates a set number designation. ;
G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ;
HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ;
K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ;

ENGINETECH : BC1002

Crankshaft Main Bearing

Maximum Clearance: 0.0005 ;
Maximum Housing Inside Diameter: 2.3228-2.3235 ;
Position: 1-5 ;
Shaft Diameter: 2.1648-2.1654 ;
Wall Thickness: 0.0781-0.0786 ;
Width: 0.669 ;

MAHLE / CLEVITE : MS2243A

Crankshaft Main Bearing

A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ;
B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
D Bearing has dowel hole.: S Indicates a set number designation. ;
G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ;
HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ;
K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ;

ITM ENGINE COMPONENTS : 5M9533

Crankshaft Main Bearing

SEALED POWER : 7469M

Crankshaft Main Bearing

Bearing 1: 72.01 mm housing bore Max; oil clearance Max 0.038 mm; Length 21.00 Max; wall thickness 2.20 Max ;
Bearing 1 Qty: 5 ;

MAHLE / CLEVITE : MS2365A

Crankshaft Main Bearing

A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ;
B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
D Bearing has dowel hole.: S Indicates a set number designation. ;
G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ;
HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ;
K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ;

MAHLE / CLEVITE : MS2268A

Crankshaft Main Bearing

A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ;
B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
D Bearing has dowel hole.: S Indicates a set number designation. ;
G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ;
HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ;
K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ;

ENGINETECH : BC1028

Crankshaft Main Bearing

ITM ENGINE COMPONENTS : 5M1046

Crankshaft Main Bearing

ENGINETECH : BC1214

Crankshaft Main Bearing

Maximum Clearance: 0.0004-0.0009 ;
Maximum Housing Inside Diameter: 1.9685-1.9692 ;
Position: 1-2-3-4-5 ;
Shaft Diameter: 1.8106-1.8110 ;
Shell Part Number: M5394-U/L ;
Wall Thickness: 0.0782-0.0787 ;
Width: 0.630 ;

ITM ENGINE COMPONENTS : 5M9530

Crankshaft Main Bearing

ITM ENGINE COMPONENTS : 4M8379

Crankshaft Main Bearing

MAHLE / CLEVITE : MS2240P

Crankshaft Main Bearing

A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ;
B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
D Bearing has dowel hole.: S Indicates a set number designation. ;
G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ;
HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ;
K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ;

ENGINETECH : BC1534

Crankshaft Main Bearing

Maximum Clearance: 0.0011-0.0031 ;
Maximum Housing Inside Diameter: 2.5984-2.5992 ;
Position: 1-4 ;
Shaft Diameter: 2.4011-2.4016 ;
Shell Part Number: T2A ;
Wall Thickness: 0.0974-0.0979 ;
Width: 0.886 ;

MAHLE / CLEVITE : MS2267A

Crankshaft Main Bearing

A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ;
B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
D Bearing has dowel hole.: S Indicates a set number designation. ;
G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ;
HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ;
K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ;

ENGINETECH : BC1543

Crankshaft Main Bearing

Maximum Clearance: 0.0016-0.0023 ;
Maximum Housing Inside Diameter: 2.8346-2.8353 ;
Position: 1-5 ;
Shaft Diameter: 2.6373-2.6378 ;
Wall Thickness: 0.0977-0.0982 ;
Width: 0.883 ;

MAHLE / CLEVITE : MS2284A

Crankshaft Main Bearing

A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ;
B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
D Bearing has dowel hole.: S Indicates a set number designation. ;
G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ;
HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ;
K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ;

MAHLE / CLEVITE : MS2336A

Crankshaft Main Bearing

A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ;
B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
D Bearing has dowel hole.: S Indicates a set number designation. ;
G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ;
HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ;
K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ;

ITM ENGINE COMPONENTS : 5M9137

Crankshaft Main Bearing

ENGINETECH : BC1042

Crankshaft Main Bearing

ENGINETECH : BC1008

Crankshaft Main Bearing

Maximum Clearance: 0.0006-0.0013 ;
Maximum Housing Inside Diameter: 2.0493-2.0498 ;
Position: 1-2-3-4-5 ;
Shaft Diameter: 1.8893-1.8897 ;
Shell Part Number: MB5287U/L ;
Wall Thickness: 0.0785-0.0790 ;
Width: 0.669 ;

SEALED POWER : 7354MA

Crankshaft Main Bearing

Part Material: A-Series aluminum ;

ENGINETECH : BC1014

Crankshaft Main Bearing

Maximum Clearance: 0.0006-0.0013 ;
Maximum Housing Inside Diameter: 2.0473-2.0478 ;
Position: 1-2-3-4-5 ;
Shaft Diameter: 1.8893-1.8897 ;
Shell Part Number: M5375U/L ;
Wall Thickness: 0.0782-0.0787 ;
Width: 0.661 ;

MAHLE / CLEVITE : MS2014A

Crankshaft Main Bearing

A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ;
B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
D Bearing has dowel hole.: S Indicates a set number designation. ;
G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ;
HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ;
K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ;

MAHLE / CLEVITE : MS2014HX

Crankshaft Main Bearing

A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ;
B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
D Bearing has dowel hole.: S Indicates a set number designation. ;
G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ;
HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ;
K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ;

MAHLE / CLEVITE : MS2014H

Crankshaft Main Bearing

A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ;
B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
D Bearing has dowel hole.: S Indicates a set number designation. ;
G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ;
HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ;
K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ;

ITM ENGINE COMPONENTS : 5M9531

Crankshaft Main Bearing

ITM ENGINE COMPONENTS : 5M9532

Crankshaft Main Bearing

ENGINETECH : BC1437

Crankshaft Main Bearing

ITM ENGINE COMPONENTS : 4M9220

Crankshaft Main Bearing

SEALED POWER : 7261M

Crankshaft Main Bearing

Part Material: Steel backed overplated bronze alloy ;

ENGINETECH : BC1435

Crankshaft Main Bearing

ITM ENGINE COMPONENTS : 5M9422

Crankshaft Main Bearing

MAHLE / CLEVITE : MS2212A

Crankshaft Main Bearing

A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ;
B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
D Bearing has dowel hole.: S Indicates a set number designation. ;
G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ;
HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ;
K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ;

SEALED POWER : 7391M

Crankshaft Main Bearing

Part Material: Steel backed overplated bronze alloy ;

新手指南

供应商服务

宜配服务

帮助

尺寸/参数

标注实例